Scan range: ±30mA/±10V
FRA/EIS: 10µHz-1MHz
Optional True Linear Scan generator
Size: 16 x 6.7 x 1.9cm
Weight: 300g
CompactStat2.h available in ±30mA/±10V, ±800mA/±10V or ±250mA/±20V configuration
CompactStat.h available in ±30mA/±100V configuration
FRA/EIS: 10µHz - 3MHz
Sampling rate up to 2MHz
Low current ranges down to 10pA
Size: 22.3 x 6.7 x 1.9cm
Weight: 350g
Grounded CE configuration allowing multiple channels in one cell
Size: 11.5 x 5.9 x 1.4cm
Weight: 125g
Compliance: 5mA@3V (2mA@6V)
FRA/EIS: 10µHz-100kHz
Size: 95 x 60 x 8mm
Weight: 50g
Instrument for introduction to electrochemistry, IviumSoft and proof-of-principle studies
Compliance: ±100mA/±21V
Optional FRA/EIS: 10µHz - 250kHz
Compliance: ±350mA/±13V
FRA/EIS: 10µHz to 1MHz as standard
Optional Bipotentiostat
Available in several current/voltage configurations
Current ranges: 100pA up to 10A
Optional FRA/EIS: 10µHz to 1MHz
Up to 8 modules/16 channels per frame (stackable up to 64 channels) can be installed
Modules can be mix and matched for maximum versatility
Multi-channel Potentiostat/Galvanostat/ZRA
Integrated impedance analyser in each channel as standard: 10µHz - 250kHz (1MHz optional)
8-channel Potentiostat/Galvanostat/ZRA
19" rack-mountable housing
Up to 128 channels/rack
Affordable high-spec electrochemical test system
Each channel: Dedicated embedded FRA/EIS
Scan range: ±5A/±10V
FRA/EIS: 10µHz to 8MHz
XP40 (±40A/±10V), XP20 (±20A/±20V), XP10 (±10A/±40V), XP5 (±5A/±100V)
Applied voltage range on XP10/20/40 is ±10V
Applied voltage range on XP5 is up to ±100V
Optional FRA/EIS: 10µHz to 500kHz
Integrated current interrupt
Direct K-type thermocouple input connector
Current compliance: 0 to +80A
Voltage compliance: +0.5 to +20V
FRA/EIS: 10µHz-10kHz
Multi-channel battery test system
Each channel: ±30mA/±10V
Optional FRA/EIS: 10µHz-20kHz on each channel for simultaneous testing
Low cost-per-channel battery test solution
Each channel: ±200mA/±10V
Each channel: ±1A/±5V
Each channel: ±3A/±5V
Multi-channel DC battery test system
Each channel: ±1A/-0.2 to +5V
High energy efficiency regenerative operation
16-channel battery test system
Each channel: ±16A/±5V or -1 to +9V
EIS: 10µHz-20kHz on each channel for simultaneous testing
Each channel: ±30mA/±10V FRA/EIS: 10µHz-100kHz (1MHz optional)
Each channel: ±200mA/±10V FRA/EIS: 10µHz-100kHz (1MHz optional)
Each channel: ±5A/±10V FRA/EIS: 10µHz-100kHz (1MHz optional)
Buy from your local reseller (US):
Scribner, LLC
Isolated 4mm electrode clips (5 per set).
